Sometimes, you can see your disk showing normally in Disk Management. Usually, this option is either under the Security tab, the Boot tab, or the Authentication tab. Find the Secure Boot option and select Disable. Restart your computer, and then press the specified key (eg: F1, F2, ESC, etc) on the initial screen to enter BIOS. Of course, you can enable Secure Boot again after cloning disk with Acronis True Image. To fix this issue, you need to disable Secure Boot in BIOS. Secure boot will be one of the reasons why Acronis clone failed. To fix Acronis True Image clone failed, here are four solutions. They are all based on the above scenarios, you can click the anchor text below and jump to the specific solution directly. This situation is very similar to the second one, but this problem is related to USB cable connected to WD disk.Ĥ Solutions to Acronis True Image WD edition clone not working Acronis True Image WD edition installation restricted - this product edition requires at least one Western Digital drive to be installed in your system.
So, you need to format exFAT to FAT32 or NTFS or turn to a professsional disk cloning software like AOMEI Backupper Professional.Įxplain: The most possible cause is that the drive does not have a valid MBR or a third party software is blocking the access to hard disk drives.ģ. Acronis not recognizing WD HD/SSD. Acronis True Image WD edition does not support exFAT file system, so Acronis won’t recognize it and you cannot use hard drive formatted as ExFAT as target drive. And most of the modern digital drive is formatted with exFAT. To clone disk, you should turn off secure boot at first.Ģ. Secure boot is a security measure built into a system's BIOS to prevent untrustworthy firmware from running. However, your computer may not reboot to recovery enviroment.Įxplain: In this case, you probably enable the secure boot in BIOS, but it does not allow this boot path as part of the cloning process. A cronis True Image not cloning after restart. When you clone disk using Acronis True Image within Windows, you will be asked to restart computer. Keep reading below to learn the situations and solutions to Acronis True Image WD edition clone not working.ģ Situations to Acronis True Image WD edition will not cloneġ.
Why Acronis WD clone failed? Is it possible to fix it? If not, is there any alternative WD disk cloning software?”ĭon't worry about too much and I'll show you how to fix it in this article.
But Acronis True Image not cloning after restart. “I got a new SSD from Western digital and then downloaded the cloning software from their website, but this software always tell me ”Acronis computer restart is required” Whenever I try to clone hard drive with it. But sometimes users may encounter the issue: Acronis True Image will not clone, below are real user case from forum. WD SSD does not come along with disk cloning software, so many users turn to Acronis True Image WD edition to repalce hard drive. P.S.User case: Acronis computer restart is required I will provide as much information as I can if you need more, but preferably I do not want the BSOD again…
I do see that the software was updated on the 20th of this month (so only a few days ago) and am wondering if the update is not stable, and if an older version would be better? I run Windows 7 64-bit.Īny help would be greatly appreciated as I want to get this sorted ASAP.
Do note though that I did uninstall Seagate before installing this WD version, and when it failed the first time I then made sure no folders of Acronis were around as well as checking through areas of the registry I could find on various forums that would need to be removed. I had installed the Seagate version of Acronis before as I was going to purchase a Seagate drive and that installed perfectly fine. Obviously, to clone the my HDD to the new one, I will need this software (as its free). There was no other important information (I think) on the blue screen. *** vididr.sys (Then the address, base at and dates)
However unfortunately during installation, my laptop crashes and goes to a blue screen with the information:
I thought it best to get ready and install the Acronis True Image provided by WD and make sure I can set the clone as soon as I got the hard drive. I have purchased a WD5000BPKT which I expect to receive on Friday.